Omron Emergency Stop Switch A165E is a direct mechanism device to open and closed communication in emergency situations, such as when they are welded to it. This is in accordance with EN 60947-5-5 including safety lock to prevent misuse. Separate construction features allow switches to be separated to facilitate wiring and construction of a single piece which allows easier handling. This is also available with three contacts built in one block (A165E-U) models.
Omron Emergency Stop Switch A165E push button switch in order to stop the state of emergency is an optional item. The features of A165E are:
1. Separation unit type (the smallest depth in the world category).
2. The circuit breaker EN418 is appropriate when there is damage, such as spot welding process circuit structure directly.
3. Install security lock to prevent wrong operation mechanism.
4. Structuring of separate keys to increasing the effectiveness of circuit wiring. You relax by using special tools to two aspects of a single structure of standing side by side.
5. One block with three types of communications product mix (types A165 E - U).
Omron 16mm Emergency Stop Switch has a positive opening mechanism with minimum 3mm contact separation in accordance with EN60947-5-1. This is including safety lock mechanism to prevent damage and "Stop reset" process to prevent accidental resets. Red button clearly visible with IP65 seal oil resistance.
For Omron Emergency Stop Switch A165E unit installations, you have to attach packing rubber or yellow panel to switch from the side of the station. Enter the switch to the panel from the front. Attach the lock ring and mounting nut from the terminal and tighten.
Then, adjust the gap in the hole and rubber packing yellow panel to the protruding unit. After that, rubber packing is not necessary when the yellow panel used. Tighten the nut to a torque 0,29-0,49 N • Casing must be fitted with a protruding portion adapted to split from hole plate. The last, you need to alignment lock ring to the groove of the casing drawn up to the edge of the side panel.
Omron Emergency Stop Switch A165E Features, You can specify your search degree only by setting requirements that suit your needs
Omron provides Omron Emergency Stop Switch as innovative solutions for various industries. You can choose the application you are looking to industry, labor and process or product categories. And the chosen application, you can specify your search degree only by setting requirements that suit your needs.Omron Emergency Stop Switch A165E push button switch in order to stop the state of emergency is an optional item. The features of A165E are:
1. Separation unit type (the smallest depth in the world category).
2. The circuit breaker EN418 is appropriate when there is damage, such as spot welding process circuit structure directly.
3. Install security lock to prevent wrong operation mechanism.
4. Structuring of separate keys to increasing the effectiveness of circuit wiring. You relax by using special tools to two aspects of a single structure of standing side by side.
5. One block with three types of communications product mix (types A165 E - U).
Omron 16mm Emergency Stop Switch has a positive opening mechanism with minimum 3mm contact separation in accordance with EN60947-5-1. This is including safety lock mechanism to prevent damage and "Stop reset" process to prevent accidental resets. Red button clearly visible with IP65 seal oil resistance.
Omron Emergency Stop Switch A165E Unit Installations to prevent accidental resets
Omron offers Omron Emergency Stop Switch safety element line such as switches, relays and sensors to adjust the safety countermeasures necessary in equipment and facilities. They are used to detect the gradual close of mechanical guard, checking infiltration into dangerous areas and the safety circuits of the building.For Omron Emergency Stop Switch A165E unit installations, you have to attach packing rubber or yellow panel to switch from the side of the station. Enter the switch to the panel from the front. Attach the lock ring and mounting nut from the terminal and tighten.
Then, adjust the gap in the hole and rubber packing yellow panel to the protruding unit. After that, rubber packing is not necessary when the yellow panel used. Tighten the nut to a torque 0,29-0,49 N • Casing must be fitted with a protruding portion adapted to split from hole plate. The last, you need to alignment lock ring to the groove of the casing drawn up to the edge of the side panel.